标签：quit EVdPdNd 示例 over PE1 PE2 PE3 DB8 2001
组网需求
如图1所示，CE2和CE3同时双归接入到PE2和PE3。要求CE1发往CE2的流量采用负载分担方式进行传输，而CE1发往CE3的流量采用非负载分担方式进行传输。
为了实现上述需求，可以基于ESI粒度设置冗余模式，即，配置CE2接入PE的冗余模式为多活跃模式，配置CE3接入PE的冗余模式设置为单活跃模式。
图1 配置EVPN VPLS over SRv6 BE（CE双归接入）组网图
配置思路
- 使能PE各接口的IPv6转发能力，配置各接口的IPv6地址。
- 在各PE上使能IS-IS，配置Level级别，指定网络实体。
- 在PE设备上配置BD模式的EVPN实例
- 在PE设备之间建立BGP EVPN对等体关系。
- 在PE设备上配置SRv6 BE。
- 在PE设备上配置将相应的BD绑定到接入侧子接口。
- 在PE上配置基于ESI粒度设置冗余模式。
- 配置CE接入PE。
操作步骤
1.使能各接口的IPv6转发能力，配置IPv6地址
<HUAWEI> system-view
[~HUAWEI] sysname PE1
[*HUAWEI] commit
[~PE1] interface gigabitethernet 1/0/0
[~PE1-GigabitEthernet1/0/0] ipv6 enable
[*PE1-GigabitEthernet1/0/0] ipv6 address 2001:DB8:10::1 64
[*PE1-GigabitEthernet1/0/0] quit
[*PE1] interface gigabitethernet 2/0/0
[*PE1-GigabitEthernet2/0/0] ipv6 enable
[*PE1-GigabitEthernet2/0/0] ipv6 address 2001:DB8:20::1 64
[*PE1-GigabitEthernet2/0/0] quit
[*PE1] interface LoopBack 1
[*PE1-LoopBack1] ip address 1.1.1.1 32
[*PE1-LoopBack1] ipv6 enable
[*PE1-LoopBack1] ipv6 address 2001:DB8:1::1 128
[*PE1-LoopBack1] quit
[*PE1] commit由于需要为EVPN源地址准备IPv4地址，因此这里Loopback接口还需配置IPv4地址。这里以PE1为例，其他设备的配置过程相同，详情可参考配置文件。
2.配置IS-IS
# 配置PE1。
[~PE1] isis 1
[*PE1-isis-1] is-level level-1
[*PE1-isis-1] cost-style wide
[*PE1-isis-1] network-entity 10.0000.0000.0001.00
[*PE1-isis-1] ipv6 enable topology ipv6
[*PE1-isis-1] quit
[*PE1] interface gigabitethernet 1/0/0
[*PE1-GigabitEthernet1/0/0] isis ipv6 enable 1
[*PE1-GigabitEthernet1/0/0] quit
[*PE1] interface gigabitethernet 2/0/0
[*PE1-GigabitEthernet2/0/0] isis ipv6 enable 1
[*PE1-GigabitEthernet2/0/0] quit
[*PE1] interface loopback1
[*PE1-LoopBack1] isis ipv6 enable 1
[*PE1-LoopBack1] commit
[~PE1-LoopBack1] quit# 配置PE2。
[~PE2] isis 1
[*PE2-isis-1] is-level level-1
[*PE2-isis-1] cost-style wide
[*PE2-isis-1] network-entity 10.0000.0000.0002.00
[*PE2-isis-1] ipv6 enable topology ipv6
[*PE2-isis-1] quit
[*PE2] interface gigabitethernet 1/0/0
[*PE2-GigabitEthernet1/0/0] isis ipv6 enable 1
[*PE2-GigabitEthernet1/0/0] quit
[*PE2] interface gigabitethernet 2/0/0
[*PE2-GigabitEthernet2/0/0] isis ipv6 enable 1
[*PE2-GigabitEthernet2/0/0] quit
[*PE2] interface loopback1
[*PE2-LoopBack1] isis ipv6 enable 1
[*PE2-LoopBack1] commit
[~PE2-LoopBack1] quit# 配置PE3。
[~PE3] isis 1
[*PE3-isis-1] is-level level-1
[*PE3-isis-1] cost-style wide
[*PE3-isis-1] network-entity 10.0000.0000.0003.00
[*PE3-isis-1] ipv6 enable topology ipv6
[*PE3-isis-1] quit
[*PE3] interface gigabitethernet 1/0/0
[*PE3-GigabitEthernet1/0/0] isis ipv6 enable 1
[*PE3-GigabitEthernet1/0/0] quit
[*PE3] interface gigabitethernet 2/0/0
[*PE3-GigabitEthernet2/0/0] isis ipv6 enable 1
[*PE3-GigabitEthernet2/0/0] quit
[*PE3] interface loopback1
[*PE3-LoopBack1] isis ipv6 enable 1
[*PE3-LoopBack1] commit
[~PE3-LoopBack1] quit配置完成后，可以执行display isis peer和display isis route命令检查IS-IS是否配置成功。以PE1为例：
[~PE1] display isis peer
Peer information for ISIS(1)
System Id Interface Circuit Id State HoldTime Type PRI
--------------------------------------------------------------------------------
0000.0000.0003* GE2/0/0 0000.0000.0003.02 Up 8s L1 64
0000.0000.0002* GE1/0/0 0000.0000.0002.02 Up 6s L1 64
Total Peer(s): 2 3.在PE设备上配置BD模式的EVPN实例
# 配置PE1。
[~PE1] evpn source-address 1.1.1.1
[*PE1] evpn vpn-instance evrf1 bd-mode
[*PE1-evpn-instance-evrf1] route-distinguisher 100:1
[*PE1-evpn-instance-evrf1] vpn-target 1:1
[*PE1-evpn-instance-evrf1] quit
[*PE1] bridge-domain 10
[*PE1-bd10] evpn binding vpn-instance evrf1
[*PE1-bd10] quit
[*PE1] evpn vpn-instance evrf2 bd-mode
[*PE1-evpn-instance-evrf2] route-distinguisher 200:1
[*PE1-evpn-instance-evrf2] vpn-target 2:2
[*PE1-evpn-instance-evrf2] quit
[*PE1] bridge-domain 20
[*PE1-bd20] evpn binding vpn-instance evrf2
[*PE1-bd20] quit
[*PE1] commit4.在PE设备之间建立BGP EVPN对等体关系
# 配置PE1。
[~PE1] bgp 100
[*PE1-bgp] router-id 1.1.1.1
[*PE1-bgp] peer 2001:DB8:3::3 as-number 100
[*PE1-bgp] peer 2001:DB8:3::3 connect-interface loopback 1
[*PE1-bgp] peer 2001:DB8:2::2 as-number 100
[*PE1-bgp] peer 2001:DB8:2::2 connect-interface loopback 1
[*PE1-bgp] l2vpn-family evpn
[*PE1-bgp-af-evpn] peer 2001:DB8:3::3 enable
[*PE1-bgp-af-evpn] peer 2001:DB8:3::3 advertise encap-type srv6
[*PE1-bgp-af-evpn] peer 2001:DB8:2::2 enable
[*PE1-bgp-af-evpn] peer 2001:DB8:2::2 advertise encap-type srv6
[*PE1-bgp-af-evpn] quit
[*PE1-bgp] quit
[*PE1] commit# 配置PE2。
[~PE2] bgp 100
[*PE2-bgp] router-id 2.2.2.2
[*PE2-bgp] peer 2001:DB8:1::1 as-number 100
[*PE2-bgp] peer 2001:DB8:1::1 connect-interface loopback 1
[*PE2-bgp] peer 2001:DB8:3::3 as-number 100
[*PE2-bgp] peer 2001:DB8:3::3 connect-interface loopback 1
[*PE2-bgp] l2vpn-family evpn
[*PE2-bgp-af-evpn] peer 2001:DB8:1::1 enable
[*PE2-bgp-af-evpn] peer 2001:DB8:1::1 advertise encap-type srv6
[*PE2-bgp-af-evpn] peer 2001:DB8:3::3 enable
[*PE2-bgp-af-evpn] peer 2001:DB8:3::3 advertise encap-type srv6
[*PE2-bgp-af-evpn] quit
[*PE2-bgp] quit
[*PE2] commit# 配置PE3。
[~PE3] bgp 100
[*PE3-bgp] router-id 3.3.3.3
[*PE3-bgp] peer 2001:DB8:1::1 as-number 100
[*PE3-bgp] peer 2001:DB8:1::1 connect-interface loopback 1
[*PE3-bgp] peer 2001:DB8:3::3 as-number 100
[*PE3-bgp] peer 2001:DB8:2::2 connect-interface loopback 1
[*PE3-bgp] l2vpn-family evpn
[*PE3-bgp-af-evpn] peer 2001:DB8:1::1 enable
[*PE3-bgp-af-evpn] peer 2001:DB8:1::1 advertise encap-type srv6
[*PE3-bgp-af-evpn] peer 2001:DB8:2::2 enable
[*PE3-bgp-af-evpn] peer 2001:DB8:2::2 advertise encap-type srv6
[*PE3-bgp-af-evpn] quit
[*PE3-bgp] quit
[*PE3] commit配置完成后，在PE设备上执行display bgp evpn peer命令，可以看到PE之间的BGP EVPN对等体关系已建立，并达到Established状态。
以PE1的显示为例：
[~PE1] display bgp evpn peer
BGP local router ID : 1.1.1.1
Local AS number : 100
Total number of peers : 2 Peers in established state : 2
Peer V AS MsgRcvd MsgSent OutQ Up/Down State PrefRcv
2001:DB8:2::2 4 100 120 125 0 01:05:04 Established 6
2001:DB8:3::3 4 100 27 27 0 00:12:15 Established 5 5.在PE设备之间建立SRv6 BE
# 配置PE1。
[~PE1] segment-routing ipv6
[*PE1-segment-routing-ipv6] encapsulation source-address 2001:DB8:1::1
[*PE1-segment-routing-ipv6] locator PE1_UNICAST ipv6-prefix 2001:DB8:11:: 64
[*PE1-segment-routing-ipv6-locator] quit
[*PE1-segment-routing-ipv6] locator PE1_BUM ipv6-prefix 2001:DB8:12:: 64 args 10
[*PE1-segment-routing-ipv6-locator] quit
[*PE1-segment-routing-ipv6] quit
[*PE1] isis 1
[*PE1-isis-1] segment-routing ipv6 locator PE1_UNICAST
[*PE1-isis-1] segment-routing ipv6 locator PE1_BUM auto-sid-disable
[*PE1-isis-1] quit
[*PE1] evpn vpn-instance evrf1 bd-mode
[*PE1-evpn-instance-evrf1] segment-routing ipv6 locator PE1_BUM unicast-locator PE1_UNICAST
[*PE1-evpn-instance-evrf1] segment-routing ipv6 best-effort
[*PE1-evpn-instance-evrf1] quit
[*PE1] evpn vpn-instance evrf2 bd-mode
[*PE1-evpn-instance-evrf2] segment-routing ipv6 locator PE1_BUM unicast-locator PE1_UNICAST
[*PE1-evpn-instance-evrf2] segment-routing ipv6 best-effort
[*PE1-evpn-instance-evrf2] quit
[*PE1] commit# 配置PE2。
[~PE2] segment-routing ipv6
[*PE2-segment-routing-ipv6] encapsulation source-address 2001:DB8:2::2
[*PE2-segment-routing-ipv6] locator PE2_UNICAST ipv6-prefix 2001:DB8:21:: 64
[*PE2-segment-routing-ipv6-locator] quit
[*PE2-segment-routing-ipv6] locator PE2_BUM ipv6-prefix 2001:DB8:22:: 64 args 10
[*PE2-segment-routing-ipv6-locator] quit
[*PE2-segment-routing-ipv6] quit
[*PE2] isis 1
[*PE2-isis-1] segment-routing ipv6 locator PE2_UNICAST
[*PE2-isis-1] segment-routing ipv6 locator PE2_BUM auto-sid-disable
[*PE2-isis-1] quit
[*PE2] evpn vpn-instance evrf1 bd-mode
[*PE2-evpn-instance-evrf1] segment-routing ipv6 locator PE2_BUM unicast-locator PE2_UNICAST
[*PE2-evpn-instance-evrf1] segment-routing ipv6 best-effort
[*PE2-evpn-instance-evrf1] quit
[*PE2] evpn vpn-instance evrf2 bd-mode
[*PE2-evpn-instance-evrf2] segment-routing ipv6 locator PE2_BUM unicast-locator PE2_UNICAST
[*PE2-evpn-instance-evrf2] segment-routing ipv6 best-effort
[*PE2-evpn-instance-evrf2] quit
[*PE2] commit# 配置PE3。
[~PE3] segment-routing ipv6
[*PE3-segment-routing-ipv6] encapsulation source-address 2001:DB8:3::3
[*PE3-segment-routing-ipv6] locator PE3_UNICAST ipv6-prefix 2001:DB8:31:: 64
[*PE3-segment-routing-ipv6-locator] quit
[*PE3-segment-routing-ipv6] locator PE3_BUM ipv6-prefix 2001:DB8:32:: 64 args 10
[*PE3-segment-routing-ipv6-locator] quit
[*PE3-segment-routing-ipv6] quit
[*PE3] isis 1
[*PE3-isis-1] segment-routing ipv6 locator PE3_UNICAST
[*PE3-isis-1] segment-routing ipv6 locator PE3_BUM auto-sid-disable
[*PE3-isis-1] quit
[*PE3] evpn vpn-instance evrf1 bd-mode
[*PE3-evpn-instance-evrf1] segment-routing ipv6 locator PE3_BUM unicast-locator PE3_UNICAST
[*PE3-evpn-instance-evrf1] segment-routing ipv6 best-effort
[*PE3-evpn-instance-evrf1] quit
[*PE3] evpn vpn-instance evrf2 bd-mode
[*PE3-evpn-instance-evrf2] segment-routing ipv6 locator PE3_BUM unicast-locator PE3_UNICAST
[*PE3-evpn-instance-evrf2] segment-routing ipv6 best-effort
[*PE3-evpn-instance-evrf2] quit
[*PE3] commit在PE上通过命令display segment-routing ipv6 local-sid { end-dt2u | end-dt2ul | end-dt2m } forwarding，查看SRv6 BE的Local SID表信息。以PE1为例：
[~PE1] display segment-routing ipv6 local-sid end-dt2m forwarding
My Local-SID End.DT2M Forwarding Table
--------------------------------------
SID : 2001:DB8:12::400:0:7800/118 FuncType : End.DT2M
Bridge-domain ID: 10
LocatorName : PE1_BUM LocatorID: 2
SID : 2001:DB8:12::400:0:7C00/118 FuncType : End.DT2M
Bridge-domain ID: 20
LocatorName : PE1_BUM LocatorID: 2
Total SID(s): 2
[~PE1] display segment-routing ipv6 local-sid end-dt2u forwarding
My Local-SID End.DT2U Forwarding Table
--------------------------------------
SID : 2001:DB8:11::1:0:20/128 FuncType : End.DT2U
Bridge-domain ID: 10
LocatorName : PE1_UNICAST LocatorID: 1
SID : 2001:DB8:11::1:0:22/128 FuncType : End.DT2U
Bridge-domain ID: 20
LocatorName : PE1_UNICAST LocatorID: 1
Total SID(s): 2 6.在PE设备上配置相应的BD绑定到接入侧子接口
# 配置PE1。
[~PE1] interface gigabitethernet 3/0/0.1 mode l2
[*PE1-GigabitEthernet3/0/0.1] encapsulation dot1q vid 10
[*PE1-GigabitEthernet3/0/0.1] rewrite pop single
[*PE1-GigabitEthernet3/0/0.1] bridge-domain 10
[*PE1-GigabitEthernet3/0/0.1] quit
[*PE1] interface gigabitethernet 3/0/0.2 mode l2
[*PE1-GigabitEthernet3/0/0.2] encapsulation dot1q vid 20
[*PE1-GigabitEthernet3/0/0.2] rewrite pop single
[*PE1-GigabitEthernet3/0/0.2] bridge-domain 20
[*PE1-GigabitEthernet3/0/0.2] quit
[*PE1] commit# 配置PE2。
[~PE2] e-trunk 1
[*PE2-e-trunk-1] priority 10
[*PE2-e-trunk-1] peer-ipv6 2001:DB8:3::3 source-ipv6 2001:DB8:2::2
[*PE2-e-trunk-1] security-key cipher 00E0FC000000
[*PE2-e-trunk-1] quit
[*PE2] e-trunk 2
[*PE2-e-trunk-2] priority 10
[*PE2-e-trunk-2] peer-ipv6 2001:DB8:3::3 source-ipv6 2001:DB8:2::2
[*PE2-e-trunk-1] security-key cipher 00E0FC000011
[*PE2-e-trunk-2] quit
[*PE2] interface eth-trunk 10
[*PE2-Eth-Trunk10] e-trunk 1
[*PE2-Eth-Trunk10] quit
[*PE2] interface eth-trunk 10.1 mode l2
[*PE2-Eth-Trunk10.1] encapsulation dot1q vid 10
[*PE2-Eth-Trunk10.1] rewrite pop single
[*PE2-Eth-Trunk10.1] bridge-domain 10
[*PE2-Eth-Trunk10.1] quit
[*PE2] interface eth-trunk 20
[*PE2-Eth-Trunk20] mode lacp-static
[*PE2-Eth-Trunk20] e-trunk 2
[*PE2-Eth-Trunk20] quit
[*PE2] interface eth-trunk 20.1 mode l2
[*PE2-Eth-Trunk20.1] encapsulation dot1q vid 20
[*PE2-Eth-Trunk20.1] rewrite pop single
[*PE2-Eth-Trunk20.1] bridge-domain 20
[*PE2-Eth-Trunk20.1] quit
[*PE2] interface gigabitethernet 3/0/0
[*PE2-GigabitEthernet3/0/0] eth-trunk 10
[*PE2-GigabitEthernet3/0/0] quit
[*PE2] interface gigabitethernet 4/0/0
[*PE2-GigabitEthernet4/0/0] eth-trunk 20
[*PE2-GigabitEthernet4/0/0] quit
[*PE2] commit# 配置PE3。
[~PE3] e-trunk 1
[*PE3-e-trunk-1] priority 10
[*PE3-e-trunk-1] peer-ipv6 2001:DB8:2::2 source-ipv6 2001:DB8:3::3
[*PE3-e-trunk-1] security-key cipher 00E0FC000000
[*PE3-e-trunk-1] quit
[*PE3] e-trunk 2
[*PE3-e-trunk-2] priority 10
[*PE3-e-trunk-2] peer-ipv6 2001:DB8:2::2 source-ipv6 2001:DB8:3::3
[*PE3-e-trunk-1] security-key cipher 00E0FC000011
[*PE3-e-trunk-2] quit
[*PE3] interface eth-trunk 10
[*PE3-Eth-Trunk10] e-trunk 1
[*PE3-Eth-Trunk10] quit
[*PE3] interface eth-trunk 10.1 mode l2
[*PE3-Eth-Trunk10.1] encapsulation dot1q vid 10
[*PE3-Eth-Trunk10.1] rewrite pop single
[*PE3-Eth-Trunk10.1] bridge-domain 10
[*PE3-Eth-Trunk10.1] quit
[*PE3] interface eth-trunk 20
[*PE3-Eth-Trunk20] mode lacp-static
[*PE3-Eth-Trunk20] e-trunk 2
[*PE3-Eth-Trunk20] quit
[*PE3] interface eth-trunk 20.1 mode l2
[*PE3-Eth-Trunk20.1] encapsulation dot1q vid 20
[*PE3-Eth-Trunk20.1] rewrite pop single
[*PE3-Eth-Trunk20.1] bridge-domain 20
[*PE3-Eth-Trunk20.1] quit
[*PE3] interface gigabitethernet 3/0/0
[*PE3-GigabitEthernet3/0/0] eth-trunk 10
[*PE3-GigabitEthernet3/0/0] quit
[*PE3] interface gigabitethernet 4/0/0
[*PE3-GigabitEthernet4/0/0] eth-trunk 20
[*PE3-GigabitEthernet4/0/0] quit
[*PE3] commit7.在PE2和PE3上配置基于ESI粒度设置冗余模式
# 配置PE2。
[~PE2] evpn
[*PE2-evpn] esi 0001.0002.0003.0004.0005
[*PE2-evpn-esi-0001.0002.0003.0004.0005] evpn redundancy-mode all-active
[*PE2-evpn-esi-0001.0002.0003.0004.0005] quit
[*PE2-evpn] esi 0005.0004.0003.0002.0001
[*PE2-evpn-esi-0005.0004.0003.0002.0001] evpn redundancy-mode single-active
[*PE2-evpn-esi-0005.0004.0003.0002.0001] quit
[*PE2-evpn] quit
[*PE2] interface Eth-Trunk 10
[*PE2-Eth-Trunk10] esi 0001.0002.0003.0004.0005
[*PE2-Eth-Trunk10] e-trunk mode force-master
[*PE2-Eth-Trunk10] quit
[*PE2] interface Eth-Trunk 20
[*PE2-Eth-Trunk20] esi 0005.0004.0003.0002.0001
[*PE2-Eth-Trunk20] e-trunk mode auto
[*PE2-Eth-Trunk20] quit
[*PE2] commit# 配置PE3。
[~PE3] evpn
[*PE3-evpn] esi 0001.0002.0003.0004.0005
[*PE3-evpn-esi-0001.0002.0003.0004.0005] evpn redundancy-mode all-active
[*PE3-evpn-esi-0001.0002.0003.0004.0005] quit
[*PE3-evpn] esi 0005.0004.0003.0002.0001
[*PE3-evpn-esi-0005.0004.0003.0002.0001] evpn redundancy-mode single-active
[*PE3-evpn-esi-0005.0004.0003.0002.0001] quit
[*PE3-evpn] quit
[*PE3] interface Eth-Trunk 10
[*PE3-Eth-Trunk10] esi 0001.0002.0003.0004.0005
[*PE3-Eth-Trunk10] e-trunk mode force-master
[*PE3-Eth-Trunk10] quit
[*PE3] interface Eth-Trunk 20
[*PE3-Eth-Trunk20] esi 0005.0004.0003.0002.0001
[*PE3-Eth-Trunk20] e-trunk mode auto
[*PE3-Eth-Trunk20] quit
[*PE3] commit8.配置CE接入PE。
# 配置CE1。
[~CE1] interface gigabitethernet 1/0/0
[~CE1-GigabitEthernet1/0/0] undo shutdown
[*CE1-GigabitEthernet1/0/0] quit
[*CE1] interface gigabitethernet 1/0/0.1
[*CE1-GigabitEthernet1/0/0.1] vlan-type dot1q 10
[*CE1-GigabitEthernet1/0/0.1] ip address 10.1.1.1 255.255.255.0
[*CE1-GigabitEthernet1/0/0.1] quit
[*CE1] interface gigabitethernet 1/0/0.2
[*CE1-GigabitEthernet1/0/0.2] vlan-type dot1q 20
[*CE1-GigabitEthernet1/0/0.2] ip address 10.2.1.1 255.255.255.0
[*CE1-GigabitEthernet1/0/0.2] quit
[*CE1] commit# 配置CE2。
[~CE2] interface Eth-Trunk10
[*CE2-Eth-Trunk10] quit
[*CE2] interface Eth-Trunk10.1
[*CE2-Eth-Trunk10.1] vlan-type dot1q 10
[*CE2-Eth-Trunk10.1] ip address 10.1.1.2 255.255.255.0
[*CE2-Eth-Trunk10.1] quit
[*CE2] interface gigabitethernet 1/0/0
[*CE2-GigabitEthernet1/0/0] undo shutdown
[*CE2-GigabitEthernet1/0/0] eth-trunk 10
[*CE2-GigabitEthernet1/0/0] quit
[*CE2] interface gigabitethernet 2/0/0
[*CE2-GigabitEthernet2/0/0] undo shutdown
[*CE2-GigabitEthernet2/0/0] eth-trunk 10
[*CE2-GigabitEthernet2/0/0] quit
[*CE2] commit# 配置CE3。
[~CE3] interface Eth-Trunk20
[*CE3-Eth-Trunk20] quit
[*CE3] interface Eth-Trunk20.1
[*CE3-Eth-Trunk20.1] vlan-type dot1q 20
[*CE3-Eth-Trunk20.1] ip address 10.2.1.2 255.255.255.0
[*CE3-Eth-Trunk20.1] quit
[*CE3] interface gigabitethernet 1/0/0
[*CE3-GigabitEthernet1/0/0] undo shutdown
[*CE3-GigabitEthernet1/0/0] eth-trunk 20
[*CE3-GigabitEthernet1/0/0] quit
[*CE3] interface gigabitethernet 2/0/0
[*CE3-GigabitEthernet2/0/0] undo shutdown
[*CE3-GigabitEthernet2/0/0] eth-trunk 20
[*CE3-GigabitEthernet2/0/0] quit
[*CE3] commit配置完成后，Eth-Trunk应该Up。在PE2和PE3上执行display eth-trunk命令查看Eth-Trunk的状态。
PE2上的显示：
[~PE2] display eth-trunk 10
Eth-Trunk10's state information is:
WorkingMode: NORMAL Hash arithmetic: According to flow
Least Active-linknumber: 1 Max Bandwidth-affected-linknumber: 32
Operate status: up Number Of Up Ports In Trunk: 1
--------------------------------------------------------------------------------
PortName Status Weight
GigabitEthernet3/0/0 Up 1
[~PE2] display eth-trunk 20
Eth-Trunk20's state information is:
WorkingMode: NORMAL Hash arithmetic: According to flow
Least Active-linknumber: 1 Max Bandwidth-affected-linknumber: 32
Operate status: down Number Of Up Ports In Trunk: 0
--------------------------------------------------------------------------------
PortName Status Weight
GigabitEthernet4/0/0 Down 1 PE3上的显示：
[~PE3] display eth-trunk 10
Eth-Trunk10's state information is:
WorkingMode: NORMAL Hash arithmetic: According to flow
Least Active-linknumber: 1 Max Bandwidth-affected-linknumber: 32
Operate status: up Number Of Up Ports In Trunk: 1
--------------------------------------------------------------------------------
PortName Status Weight
GigabitEthernet4/0/0 Up 1
[~PE3] display eth-trunk 20
Eth-Trunk20's state information is:
WorkingMode: NORMAL Hash arithmetic: According to flow
Least Active-linknumber: 1 Max Bandwidth-affected-linknumber: 32
Operate status: up Number Of Up Ports In Trunk: 1
--------------------------------------------------------------------------------
PortName Status Weight
GigabitEthernet3/0/0 Up 1 从显示信息可以看出，对于Eth-Trunk 10，PE2和PE3是双主状态；对于Eth-Trunk 20，PE2处于备状态，PE3处于主状态。
9.检查配置结果
在PE上通过配置命令display bgp evpn all routing-table，可以看到远端发来的EVPN路由。以PE1为例：
[~PE1] display bgp evpn all routing-table
Local AS number : 100
BGP Local router ID is 1.1.1.1
Status codes: * - valid, > - best, d - damped, x - best external, a - add path,
h - history, i - internal, s - suppressed, S - Stale
Origin : i - IGP, e - EGP, ? - incomplete
EVPN address family:
Number of A-D Routes: 7
Route Distinguisher: 100:1
Network(ESI/EthTagId) NextHop
*>i 0001.0002.0003.0004.0005:0 2001:DB8:2::2
* i 2001:DB8:3::3
Route Distinguisher: 200:1
Network(ESI/EthTagId) NextHop
*>i 0005.0004.0003.0002.0001:0 2001:DB8:2::2
* i 2001:DB8:3::3
Route Distinguisher: 2.2.2.2:0
Network(ESI/EthTagId) NextHop
*>i 0001.0002.0003.0004.0005:4294967295 2001:DB8:2::2
Route Distinguisher: 3.3.3.3:0
Network(ESI/EthTagId) NextHop
*>i 0001.0002.0003.0004.0005:4294967295 2001:DB8:3::3
*>i 0005.0004.0003.0002.0001:4294967295 2001:DB8:3::3
EVPN-Instance evrf1:
Number of A-D Routes: 4
Network(ESI/EthTagId) NextHop
*>i 0001.0002.0003.0004.0005:0 2001:DB8:2::2
* i 2001:DB8:3::3
*>i 0001.0002.0003.0004.0005:4294967295 2001:DB8:2::2
* i 2001:DB8:3::3
EVPN-Instance evrf2:
Number of A-D Routes: 3
Network(ESI/EthTagId) NextHop
*>i 0005.0004.0003.0002.0001:0 2001:DB8:3::3
i 2001:DB8:2::2
*>i 0005.0004.0003.0002.0001:4294967295 2001:DB8:3::3
EVPN address family:
Number of Mac Routes: 3
Route Distinguisher: 100:1
Network(EthTagId/MacAddrLen/MacAddr/IpAddrLen/IpAddr) NextHop
*>i 0:48:38c2-6721-0300:0:0.0.0.0 2001:DB8:2::2
* i 2001:DB8:3::3
Route Distinguisher: 200:1
Network(EthTagId/MacAddrLen/MacAddr/IpAddrLen/IpAddr) NextHop
*> 0:48:38c2-6721-0300:0:0.0.0.0 0.0.0.0
EVPN-Instance evrf1:
Number of Mac Routes: 3
Network(EthTagId/MacAddrLen/MacAddr/IpAddrLen/IpAddr) NextHop
*> 0:48:38c2-6721-0300:0:0.0.0.0 0.0.0.0
* i 2001:DB8:2::2
* i 2001:DB8:3::3
EVPN-Instance evrf2:
Number of Mac Routes: 1
Network(EthTagId/MacAddrLen/MacAddr/IpAddrLen/IpAddr) NextHop
*> 0:48:38c2-6721-0300:0:0.0.0.0 0.0.0.0
EVPN address family:
Number of Inclusive Multicast Routes: 6
Route Distinguisher: 100:1
Network(EthTagId/IpAddrLen/OriginalIp) NextHop
*> 0:32:1.1.1.1 127.0.0.1
*>i 0:32:2.2.2.2 2001:DB8:2::2
*>i 0:32:3.3.3.3 2001:DB8:3::3
Route Distinguisher: 200:1
Network(EthTagId/IpAddrLen/OriginalIp) NextHop
*> 0:32:1.1.1.1 127.0.0.1
*>i 0:32:2.2.2.2 2001:DB8:2::2
*>i 0:32:3.3.3.3 2001:DB8:3::3
EVPN-Instance evrf1:
Number of Inclusive Multicast Routes: 3
Network(EthTagId/IpAddrLen/OriginalIp) NextHop
*> 0:32:1.1.1.1 127.0.0.1
*>i 0:32:2.2.2.2 2001:DB8:2::2
*>i 0:32:3.3.3.3 2001:DB8:3::3
EVPN-Instance evrf2:
Number of Inclusive Multicast Routes: 3
Network(EthTagId/IpAddrLen/OriginalIp) NextHop
*> 0:32:1.1.1.1 127.0.0.1
*>i 0:32:2.2.2.2 2001:DB8:2::2
*>i 0:32:3.3.3.3 2001:DB8:3::3 在PE1上通过配置命令display bgp evpn all routing-table ad-route，可以看到远端发来的EVPN路由的详细信息。
查看ESI 0001.0002.0003.0004.0005的路由。从ESI Label字段可知，ESI 0001.0002.0003.0004.0005形成了双归双活。
[~PE1] display bgp evpn all routing-table ad-route 0001.0002.0003.0004.0005:4294967295
BGP local router ID : 1.1.1.1
Local AS number : 100
Total routes of Route Distinguisher(2.2.2.2:0): 1
BGP routing table entry information of 0001.0002.0003.0004.0005:4294967295:
From: 2001:DB8:2::2 (2.2.2.2)
Route Duration: 0d00h31m39s
Relay IP Nexthop: FE80::3AC2:67FF:FE31:307
Relay IP Out-Interface:GigabitEthernet1/0/0
Relay Tunnel Out-Interface:
Original nexthop: 2001:DB8:2::2
Qos information : 0x0
Ext-Community: RT <1 : 1>, ESI Label<0 : 0 : 48066>
Prefix-sid: ::1
AS-path Nil, origin incomplete, localpref 100, pref-val 0, valid, internal, best, select, pre 255, IGP cost 10
Route Type: 1 (Ethernet Auto-Discovery (A-D) route)
ESI: 0001.0002.0003.0004.0005, Ethernet Tag ID: 4294967295
Not advertised to any peer yet
Total routes of Route Distinguisher(3.3.3.3:0): 1
BGP routing table entry information of 0001.0002.0003.0004.0005:4294967295:
From: 2001:DB8:3::3 (3.3.3.3)
Route Duration: 0d00h30m23s
Relay IP Nexthop: FE80::3AC2:67FF:FE41:305
Relay IP Out-Interface:GigabitEthernet2/0/0
Relay Tunnel Out-Interface:
Original nexthop: 2001:DB8:3::3
Qos information : 0x0
Ext-Community: RT <1 : 1>, ESI Label<0 : 0 : 48066>
Prefix-sid: ::1
AS-path Nil, origin incomplete, localpref 100, pref-val 0, valid, internal, best, select, pre 255, IGP cost 10
Route Type: 1 (Ethernet Auto-Discovery (A-D) route)
ESI: 0001.0002.0003.0004.0005, Ethernet Tag ID: 4294967295
Not advertised to any peer yet
EVPN-Instance evrf1:
Number of A-D Routes: 2
BGP routing table entry information of 0001.0002.0003.0004.0005:4294967295:
Route Distinguisher: 2.2.2.2:0
Remote-Cross route
From: 2001:DB8:2::2 (2.2.2.2)
Route Duration: 0d00h31m53s
Relay IP Nexthop: FE80::3AC2:67FF:FE31:307
Relay IP Out-Interface:GigabitEthernet1/0/0
Relay Tunnel Out-Interface:
Original nexthop: 2001:DB8:2::2
Qos information : 0x0
Ext-Community: RT <1 : 1>, ESI Label<0 : 0 : 48066>
Prefix-sid: ::1
AS-path Nil, origin incomplete, localpref 100, pref-val 0, valid, internal, best, select, pre 255, IGP cost 10
Route Type: 1 (Ethernet Auto-Discovery (A-D) route)
ESI: 0001.0002.0003.0004.0005, Ethernet Tag ID: 4294967295
Not advertised to any peer yet
BGP routing table entry information of 0001.0002.0003.0004.0005:4294967295:
Route Distinguisher: 3.3.3.3:0
Remote-Cross route
From: 2001:DB8:3::3 (3.3.3.3)
Route Duration: 0d00h30m38s
Relay IP Nexthop: FE80::3AC2:67FF:FE41:305
Relay IP Out-Interface:GigabitEthernet2/0/0
Relay Tunnel Out-Interface:
Original nexthop: 2001:DB8:3::3
Qos information : 0x0
Ext-Community: RT <1 : 1>, ESI Label<0 : 0 : 48066>
Prefix-sid: ::1
AS-path Nil, origin incomplete, localpref 100, pref-val 0, valid, internal, pre 255, IGP cost 10, not preferred for router ID
Route Type: 1 (Ethernet Auto-Discovery (A-D) route)
ESI: 0001.0002.0003.0004.0005, Ethernet Tag ID: 4294967295
Not advertised to any peer yet 查看ESI 0005.0004.0003.0002.0001的路由。从ESI Label字段可知，ESI 0005.0004.0003.0002.0001形成了双归单活。
[~PE1] display bgp evpn all routing-table ad-route 0005.0004.0003.0002.0001:4294967295
BGP local router ID : 1.1.1.1
Local AS number : 100
Total routes of Route Distinguisher(3.3.3.3:0): 1
BGP routing table entry information of 0005.0004.0003.0002.0001:4294967295:
From: 2001:DB8:3::3 (3.3.3.3)
Route Duration: 0d00h33m11s
Relay IP Nexthop: FE80::3AC2:67FF:FE41:305
Relay IP Out-Interface:GigabitEthernet2/0/0
Relay Tunnel Out-Interface:
Original nexthop: 2001:DB8:3::3
Qos information : 0x0
Ext-Community: RT <2 : 2>, ESI Label<1 : 0 : 48067>
Prefix-sid: ::2
AS-path Nil, origin incomplete, localpref 100, pref-val 0, valid, internal, best, select, pre 255, IGP cost 10
Route Type: 1 (Ethernet Auto-Discovery (A-D) route)
ESI: 0005.0004.0003.0002.0001, Ethernet Tag ID: 4294967295
Not advertised to any peer yet
EVPN-Instance evrf2:
Number of A-D Routes: 1
BGP routing table entry information of 0005.0004.0003.0002.0001:4294967295:
Route Distinguisher: 3.3.3.3:0
Remote-Cross route
From: 2001:DB8:3::3 (3.3.3.3)
Route Duration: 0d00h33m11s
Relay IP Nexthop: FE80::3AC2:67FF:FE41:305
Relay IP Out-Interface:GigabitEthernet2/0/0
Relay Tunnel Out-Interface:
Original nexthop: 2001:DB8:3::3
Qos information : 0x0
Ext-Community: RT <2 : 2>, ESI Label<1 : 0 : 48067>
Prefix-sid: ::2
AS-path Nil, origin incomplete, localpref 100, pref-val 0, valid, internal, best, select, pre 255, IGP cost 10
Route Type: 1 (Ethernet Auto-Discovery (A-D) route)
ESI: 0005.0004.0003.0002.0001, Ethernet Tag ID: 4294967295
Not advertised to any peer yet CE1能够相互Ping通CE2和CE3，例如：
[~CE1] ping 10.1.1.2
PING 10.1.1.2: 56 data bytes, press CTRL_C to break
Reply from 10.1.1.2: bytes=56 Sequence=1 ttl=255 time=224 ms
Reply from 10.1.1.2: bytes=56 Sequence=2 ttl=255 time=10 ms
Reply from 10.1.1.2: bytes=56 Sequence=3 ttl=255 time=10 ms
Reply from 10.1.1.2: bytes=56 Sequence=4 ttl=255 time=9 ms
Reply from 10.1.1.2: bytes=56 Sequence=5 ttl=255 time=10 ms
--- 10.1.1.2 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 9/52/224 ms
[~CE1] ping 10.2.1.2
PING 10.2.1.2: 56 data bytes, press CTRL_C to break
Reply from 10.2.1.2: bytes=56 Sequence=1 ttl=255 time=12 ms
Reply from 10.2.1.2: bytes=56 Sequence=2 ttl=255 time=10 ms
Reply from 10.2.1.2: bytes=56 Sequence=3 ttl=255 time=7 ms
Reply from 10.2.1.2: bytes=56 Sequence=4 ttl=255 time=11 ms
Reply from 10.2.1.2: bytes=56 Sequence=5 ttl=255 time=7 ms
--- 10.2.1.2 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 7/9/12 ms 标签：quit,EVdPdNd,示例,over,PE1,PE2,PE3,DB8,2001 来源： https://blog.csdn.net/guolianggsta/article/details/122829491
本站声明： 1. iCode9 技术分享网（下文简称本站）提供的所有内容，仅供技术学习、探讨和分享； 2. 关于本站的所有留言、评论、转载及引用，纯属内容发起人的个人观点，与本站观点和立场无关； 3. 关于本站的所有言论和文字，纯属内容发起人的个人观点，与本站观点和立场无关； 4. 本站文章均是网友提供，不完全保证技术分享内容的完整性、准确性、时效性、风险性和版权归属；如您发现该文章侵犯了您的权益，可联系我们第一时间进行删除； 5. 本站为非盈利性的个人网站，所有内容不会用来进行牟利，也不会利用任何形式的广告来间接获益，纯粹是为了广大技术爱好者提供技术内容和技术思想的分享性交流网站。