[开发参考]一种灯光遥控器的红外参数

2022-01-26 18:06:58 阅读：195 来源： 互联网

标签：1620 灯光 570 红外遥控器 530 620 1670 480

搜索关键词：红外 LED 吸顶灯遥控器变色智能灯具无极调光灯泡遥控手柄

这种遥控器的结构较为简单，其中含有一个不含识别码的记忆模块TL HW12（拆开壳就看得到了），因此可以通过接收器完全获取其中的按键发送的红外数据。在这里我使用了arduino进行截取，获取了以下的红外信号数据。所有信号都已经对应图进行了标注。
下属数据截止本文发布时实测有效

private int[] rawData_nightlight = {8730,4420, 530,570, 530,570, 530,570, 480,620, 480,570, 530,570, 530,570, 530,1620, 530,1670, 480,1670, 530,1620, 530,1620, 530,1670, 480,1670, 530,1620, 530,570, 530,1620, 530,570, 530,1620, 530,570, 530,570, 530,570, 530,520, 530,620, 480,620, 480,1670, 480,620, 480,1670, 480,1670, 530,1620, 530,1670, 480,1620, 530};  		
private int[] rawData_On = {8730,4420, 480,570, 530,570, 530,570, 530,570, 480,620, 480,620, 480,570, 530,1670, 480,1670, 530,1620, 530,1620, 530,1670, 480,1670, 530,1620, 530,1620, 530,570, 530,1670, 480,570, 530,570, 530,570, 530,570, 480,620, 480,620, 480,570, 530,570, 530,1620, 530,1670, 480,1670, 530,1620, 530,1620, 530,1670, 480,1670, 530};  				
private int[] rawData_Off = {8730,4420, 530,570, 480,620, 480,620, 480,570, 530,570, 530,570, 530,570, 480,1670, 530,1620, 530,1670, 480,1670, 530,1620, 530,1620, 530,1670, 480,1670, 530,570, 480,1670, 530,570, 530,570, 480,620, 480,570, 530,570, 530,570, 530,570, 530,570, 480,1670, 530,1620, 530,1620, 530,1670, 480,1670, 530,1620, 530,1670, 480};  				
private int[] rawData_arrow_up = {8730,4420, 480,570, 530,570, 530,570, 530,570, 530,570, 530,570, 480,620, 480,1670, 480,1670, 530,1620, 530,1670, 480,1670, 530,1620, 530,1620, 530,1670, 480,620, 480,570, 530,1670, 480,620, 480,570, 530,1670, 480,570, 530,570, 530,570, 530,1620, 530,570, 530,1670, 480,1670, 480,620, 480,1670, 530,1620, 530,1620, 530};  		
private int[] rawData_arrow_left = {8730,4420, 530,570, 530,570, 480,620, 480,570, 530,570, 530,570, 530,570, 530,1620, 530,1620, 530,1670, 480,1670, 530,1620, 530,1620, 530,1670, 480,1670, 530,570, 480,620, 480,1670, 530,1620, 530,1620, 530,1670, 480,620, 480,570, 530,570, 530,1670, 480,570, 530,570, 530,570, 530,570, 480,1670, 530,1620, 530,1670, 480};  		
private int[] rawData_lightness = {8730,4370, 530,620, 480,570, 530,570, 530,570, 530,570, 530,570, 480,620, 480,1670, 480,1670, 530,1620, 530,1670, 480,1670, 530,1620, 530,1620, 530,1670, 480,620, 480,1670, 480,1670, 530,1620, 530,1670, 480,1620, 580,1620, 530,1620, 530,1670, 480,620, 480,570, 530,570, 530,570, 530,570, 480,620, 480,620, 480,570, 530};  		
private int[] rawData_arrow_right = {8730,4420, 480,620, 480,570, 530,570, 530,570, 530,570, 530,570, 480,620, 480,1670, 480,1670, 530,1620, 530,1620, 530,1670, 530,1620, 530,1620, 530,1670, 480,620, 480,570, 530,1670, 480,620, 480,570, 530,1670, 480,570, 530,570, 530,570, 530,1620, 530,570, 530,1670, 480,1670, 480,620, 480,1670, 480,1670, 530,1620, 530};  		
private int[] rawData_arrow_down = {8780,4370, 530,570, 530,570, 530,570, 530,570, 480,620, 480,570, 530,570, 530,1670, 480,1670, 480,1670, 530,1620, 530,1670, 480,1670, 480,1670, 530,1620, 530,570, 530,570, 530,1620, 530,1670, 480,1670, 530,1620, 530,570, 530,570, 480,620, 480,1670, 530,570, 480,620, 480,570, 530,570, 530,1670, 480,1670, 480,1670, 530};  		
private int[] rawData_auxiliary1 = {8730,4420, 530,570, 530,570, 530,570, 480,620, 480,570, 530,570, 530,570, 530,1620, 530,1620, 530,1670, 480,1670, 530,1620, 530,1670, 480,1670, 530,1620, 530,570, 530,570, 530,1620, 530,570, 530,1620, 530,1670, 480,570, 530,570, 530,570, 530,1620, 530,570, 530,1620, 530,570, 530,570, 530,1620, 530,1670, 480,1670, 480};  		
private int[] rawData_auxiliary2 = {8730,4370, 530,620, 480,570, 530,570, 530,570, 530,570, 480,620, 480,620, 480,1670, 480,1670, 530,1620, 530,1670, 480,1670, 480,1670, 530,1620, 530,1670, 480,570, 530,570, 530,1670, 480,570, 530,1670, 480,1670, 480,620, 480,620, 480,570, 530,1670, 480,570, 530,1670, 480,620, 480,570, 530,1670, 480,1670, 530,1620, 530};  		
private int[] rawData_auxiliary3 = {8730,4420, 530,570, 530,570, 530,570, 530,570, 480,620, 480,570, 530,570, 530,1670, 480,1670, 480,1670, 530,1620, 530,1670, 480,1670, 480,1670, 530,1620, 530,570, 530,570, 530,1620, 530,570, 530,1670, 480,1670, 480,620, 480,570, 530,570, 530,1670, 480,570, 530,1670, 480,620, 480,570, 530,1670, 480,1670, 530,1620, 530};  		
private int[] rawData_warmth_decrease = {8730,4420, 530,570, 530,570, 480,620, 480,620, 480,570, 530,570, 530,570, 530,1620, 530,1670, 480,1670, 480,1670, 530,1620, 530,1670, 480,1670, 530,1620, 530,570, 530,1620, 530,1670, 480,570, 530,570, 530,570, 530,570, 530,570, 480,620, 480,620, 480,570, 530,1670, 480,1670, 480,1670, 530,1620, 530,1670, 480,1670, 480};  	
private int[] rawData_warmth_increase = {8730,4370, 530,620, 480,570, 530,570, 530,570, 530,570, 530,570, 480,620, 480,1670, 480,1670, 530,1620, 530,1670, 480,1670, 530,1620, 530,1620, 530,1670, 480,620, 480,570, 530,1670, 480,620, 530,520, 530,570, 530,570, 530,570, 530,570, 480,1670, 530,570, 480,1670, 530,1620, 530,1670, 480,1670, 530,1620, 530,1620, 530};  	
private int[] rawData_segment = {8730,4420, 480,570, 530,570, 530,570, 530,570, 480,620, 480,570, 530,570, 530,1670, 480,1670, 480,1670, 530,1620, 530,1670, 480,1670, 480,1670, 530,1620, 530,570, 530,570, 530,1620, 530,1670, 480,570, 530,570, 530,570, 530,570, 480,620, 480,1670, 530,570, 480,620, 480,1670, 480,1670, 530,1620, 530,1670, 480,1670, 480};

可以通过上述红外信号设计一个红外发射app，用于取代遥控器。
详见我创建的Github项目，其中已经发布了一个可用的版本。

另附：ardiuno接收红外信号（使用VS1838B）的示例代码（来源于公开的红外库）

所收取的数据就是rawdata段

/*
 * ReceiveDump.cpp
 *
 * Dumps the received signal in different flavors.
 * Since the printing takes so much time, repeat signals may be skipped or interpreted as UNKNOWN.
 *
 *  This file is part of Arduino-IRremote https://github.com/Arduino-IRremote/Arduino-IRremote.
 *
 ************************************************************************************
 * MIT License
 *
 * Copyright (c) 2020-2021 Armin Joachimsmeyer
 *
 * Permission is hereby granted, free of charge, to any person obtaining a copy
 * of this software and associated documentation files (the "Software"), to deal
 * in the Software without restriction, including without limitation the rights
 * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
 * copies of the Software, and to permit persons to whom the Software is furnished
 * to do so, subject to the following conditions:
 *
 * The above copyright notice and this permission notice shall be included in all
 * copies or substantial portions of the Software.
 *
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
 * INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
 * PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
 * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF
 * CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE
 * OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
 *
 ************************************************************************************
 */
#include <Arduino.h>

//#define RAW_BUFFER_LENGTH  750  // 750 is the value for air condition remotes.

/*
 * Define macros for input and output pin etc.
 */
#include "PinDefinitionsAndMore.h"

/*
 * You can change this value accordingly to the receiver module you use.
 * The required value can be derived from the timings printed here.
 * Keep in mind that the timings may change with the distance
 * between sender and receiver as well as with the ambient light intensity.
 */
#define MARK_EXCESS_MICROS    20 // recommended for the cheap VS1838 modules

//#define RECORD_GAP_MICROS 12000 // Activate it for some LG air conditioner protocols
//#define DEBUG // Activate this for lots of lovely debug output from the decoders.
#define INFO // To see valuable informations from universal decoder for pulse width or pulse distance protocols

#include <IRremote.hpp>

//+=============================================================================
// Configure the Arduino
//
void setup() {
    pinMode(LED_BUILTIN, OUTPUT);

    Serial.begin(115200);   // Status message will be sent to PC at 9600 baud
#if defined(__AVR_ATmega32U4__) || defined(SERIAL_USB) || defined(SERIAL_PORT_USBVIRTUAL)  || defined(ARDUINO_attiny3217)
    delay(4000); // To be able to connect Serial monitor after reset or power up and before first print out. Do not wait for an attached Serial Monitor!
#endif
    // Just to know which program is running on my Arduino
    Serial.println(F("START " __FILE__ " from " __DATE__ "\r\nUsing library version " VERSION_IRREMOTE));

    IrReceiver.begin(IR_RECEIVE_PIN, ENABLE_LED_FEEDBACK); // Start the receiver, enable feedback LED, take LED feedback pin from the internal boards definition

    Serial.print(F("Ready to receive IR signals of protocols: "));
    printActiveIRProtocols(&Serial);
    Serial.print(F("at pin "));
    Serial.println(IR_RECEIVE_PIN);
}

//+=============================================================================
// The repeating section of the code
//
void loop() {
    if (IrReceiver.decode()) {  // Grab an IR code
        // Check if the buffer overflowed
        if (IrReceiver.decodedIRData.flags & IRDATA_FLAGS_WAS_OVERFLOW) {
            Serial.println(F("Overflow detected"));
            Serial.println(F("Try to increase the \"RAW_BUFFER_LENGTH\" value of " STR(RAW_BUFFER_LENGTH) " in " __FILE__));
            // see also https://github.com/Arduino-IRremote/Arduino-IRremote#modifying-compile-options-with-sloeber-ide
        } else {
            Serial.println();                               // 2 blank lines between entries
            Serial.println();
            IrReceiver.printIRResultShort(&Serial);
            Serial.println();
            Serial.println(F("Raw result in internal ticks (50 us) - with leading gap"));
            IrReceiver.printIRResultRawFormatted(&Serial, false); // Output the results in RAW format
            Serial.println(F("Raw result in microseconds - with leading gap"));
            IrReceiver.printIRResultRawFormatted(&Serial, true);  // Output the results in RAW format
            Serial.println();                               // blank line between entries
            Serial.print(F("Result as internal ticks (50 us) array - compensated with MARK_EXCESS_MICROS="));
            Serial.println(MARK_EXCESS_MICROS);
            IrReceiver.compensateAndPrintIRResultAsCArray(&Serial, false); // Output the results as uint8_t source code array of ticks
            Serial.print(F("Result as microseconds array - compensated with MARK_EXCESS_MICROS="));
            Serial.println(MARK_EXCESS_MICROS);
            IrReceiver.compensateAndPrintIRResultAsCArray(&Serial, true); // Output the results as uint16_t source code array of micros
            IrReceiver.printIRResultAsCVariables(&Serial);  // Output address and data as source code variables

            IrReceiver.compensateAndPrintIRResultAsPronto(&Serial);

            /*
             * Example for using the compensateAndStorePronto() function.
             * Creating this String requires 2210 bytes program memory and 10 bytes RAM for the String class.
             * The String object itself requires additional 440 Bytes RAM from the heap.
             * This values are for an Arduino UNO.
             */
//        Serial.println();                                     // blank line between entries
//        String ProntoHEX = F("Pronto HEX contains: ");        // Assign string to ProtoHex string object
//        if (int size = IrReceiver.compensateAndStorePronto(&ProntoHEX)) {   // Dump the content of the IReceiver Pronto HEX to the String object
//            // Append compensateAndStorePronto() size information to the String object (requires 50 bytes heap)
//            ProntoHEX += F("\r\nProntoHEX is ");              // Add codes size information to the String object
//            ProntoHEX += size;
//            ProntoHEX += F(" characters long and contains "); // Add codes count information to the String object
//            ProntoHEX += size / 5;
//            ProntoHEX += F(" codes");
//            Serial.println(ProntoHEX.c_str());                // Print to the serial console the whole String object
//            Serial.println();                                 // blank line between entries
//        }
        }
        IrReceiver.resume();                            // Prepare for the next value
    }
}

标签：1620,灯光,570,红外,遥控器,530,620,1670,480
来源： https://www.cnblogs.com/holittech/p/ir_remoter_ref1.html

本站声明： 1. iCode9 技术分享网（下文简称本站）提供的所有内容，仅供技术学习、探讨和分享；
2. 关于本站的所有留言、评论、转载及引用，纯属内容发起人的个人观点，与本站观点和立场无关；
3. 关于本站的所有言论和文字，纯属内容发起人的个人观点，与本站观点和立场无关；
4. 本站文章均是网友提供，不完全保证技术分享内容的完整性、准确性、时效性、风险性和版权归属；如您发现该文章侵犯了您的权益，可联系我们第一时间进行删除；
5. 本站为非盈利性的个人网站，所有内容不会用来进行牟利，也不会利用任何形式的广告来间接获益，纯粹是为了广大技术爱好者提供技术内容和技术思想的分享性交流网站。

ICode9

[开发参考]一种灯光遥控器的红外参数